How to Make a Spinning Top Easily – Hip Hop You Don’t Top

As an Amazon Associate we earn from qualifying purchases (more).

Featured

If you’re looking for a simple toy project that you can knock out in bulk as quick gifts, party favors, craft fair items or official currency in some alternate universe where tops are tops, the simple, timeless joy of a spinning top is as easy to achieve as it gets. It’s also a great beginner project to get the kids and grandchildren involved.

How to Make a Spinning Top – Let’s Take It From The Top

Spinning top parts
Only two parts are required to make the spinning tops.

First of all, let me mention that I made all 25 tops you see in one evening. It really is something you can make in bulk without a huge time investment. The secret is in the method. Rather than turn tops on a lathe, (though a good lathe operator could arguably make them fairly quickly as well), I just combined parts I already had.

The axles are 1/4” poplar dowel from the home center. All 25 of mine were cut from a single 48” dowel.

Flywheels
Hole saw off-cuts and craft store wheels make perfect flywheels.

The other component is the flywheel. The two flywheels pictured in the top row are hole saw cutouts left over from other projects. The ones in the bottom row are “craft” wheels that you can buy from most craft supply dealers. All of my flywheels happen to have a 1/4” center hole. Whatever size hole is in yours, just choose an appropriately sized dowel. 1/4” seems to be about perfect though and would be my recommendation.

Get Right To The Point

Tapering
Taper one end with a pencil sharpener.

The first step is to taper one end of the dowel with a pencil sharpener. You don’t want a needle point. A tiny amount of flatness at the tip is ideal. After a few you’ll get it just right. You can always use fine sandpaper to adjust the point if needed.

The point
Leave a slight amount of flatness at the very tip of the point.

On The Fly

Assembled
Flywheel on axle.

Slide your flywheel of choice onto the axle from the pointy end. I found that the best location for the flywheel is usually right above the top of the taper. With larger diameter flywheels, you can often afford to raise it a little higher. Keep in mind that the higher the mass the more unstable the top tends to become. So it’s generally preferable to keep it fairly low, but not so low that it’s going to keep bottoming out on the tabletop.

If you use craft wheels, install them with the decorative side up and the flat, boring side towards the point.

Trim A Little Off The Top

Cutting
Cutting the top apart from the rest of the dowel.

After you’ve slid the flywheel slightly above the top of the taper, it’s time to cut the axle free from the rest of the dowel. You want to leave more axle length above the flywheel than below. I judged mine from an aesthetic standpoint and found the proportions to be pretty much perfect. Since I eyeballed mine, they vary quite a bit. The following dimensions will serve as guidance, should you need it. They all produced well balanced tops:

Proportions will be expressed in the following format:
“Fly dia @ thickness > Axle length above flywheel”:
1” @ 1/2” > 11/16”
1” @ 3/8” > 11/16”
1-1/4” @ 3/8” > 13/16”
1-1/4” @ 3/4” > 1-1/16”
2” @ 1/4” > 1-1/2”

By no means must your tops be restricted to the dimensions given above. Those are just what looked right and worked well for me. There’s plenty of room for variation.

Roundover
Sanding a roundover at the top of the axle.

Sand a roundover to soften the cut you just made. It doesn’t take much.

Spin Spinna You Don’t Quit; Spin It! (Takin’ ‘er For A Spin)

Give the top a few test spins on a flat, smooth surface and adjust the height of the flywheel as needed for stability. If the dowel fits snugly in the hole, twisting the flywheel will break the friction, making it easier to move along the length of the dowel.

Sticking To What Works

Gluing
After fine tuning, bond the flywheel and axle together with thin CA glue.

Once your flywheel is located where your want it, run a line of CA (“super”) glue on the underside of the flywheel, along the axle joint to ensure that things stay put from here on out.

Top of Your Game

In motion
Top in motion.

You could stop here and call it complete. But if you want to liven things up a bit, use permanent markers to add color. Adding color is as simple as bracing your marker holding hand and rotating the top with the other hand.

Coloring
Color with permanent markers by holding the marker still and rotating the top.
Colored
Adding color really livens things up.

See what cool color combinations and patterns you can come up with.

More examples

Color in motion
Color in motion.

Some patterns take on a whole different appearance or even seem to change color when in motion.

Motion blur
Many patterns change when in motion.
Vanishing bars
Some design elements may completely vanish while spinning.

Finish your tops with a few coats of clear lacquer from a spray can and you’re done.

The Spin Zone

If you want to make something cool but don’t have the time or energy for anything too involved, this is the project for you. Your top will be spinning long before your head ever has a chance to!

Here are a few craft stores with wooden wheels to get you started:

Buy Now - via Bear Woods


Buy Now - via CraftParts.com


Buy Now - via Michaels

Photo of author

About Steve

Steve made his first woodworking project at age 9 (in 1982) and whittled his first wooden chain at 18. He was also a consumer electronics repair tech and shop owner for a little over 20 years, until his impending obsolescence became impossible to ignore. Since then, Steve has focused passionately on manipulating his wood... in his workshop. Don't judge him.

Subscribe to our newsletter

Get access to free prizes, product sneak-peeks, reviews, how-to's and much more!

More Info | Email Privacy

8 thoughts on “How to Make a Spinning Top Easily – Hip Hop You Don’t Top”

  1. Thanks for coming up with another woodworking project that’s within my skill set. I’ll be babysitting my 2-1/2 year old grandson for a few days, and this looks like a great project to do together. It’s something we should be able to finish within his limited attention span (which happens to coincide with MY attention span), and it will give him some good practice using Super Glue and the band saw. And before any outraged parents start calling Child Protective Services, relax – I was kidding. He’ll actually be using the scroll saw, naturally.

    Reply
    • It would be a great project to get the kids involved. They’ll have a working toy pretty quickly and get to be creative with the coloring. They won’t even have time to get bored!

      Reply

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.