Ramset MasterShot – How To Nail It When It’s Built Like A Brick, Um, Outhouse

As an Amazon Associate we earn from qualifying purchases (more).

ramset mastershot

About three years ago, while temporarily off my meds, I volunteered to help my son create a bedroom in his previously unfinished basement. We put 2X4 pressure treated sleepers down over the concrete floor and on the concrete block walls. We put plywood down for the floor, capped it off with laminate flooring, and insulated and drywalled the walls. By far the biggest pain in the ass of the entire project (aside from hauling everything down there) was attaching the sleepers to the floor and walls. We used a hammer drill and Tapcon screws, which hold great, but which are extremely labor intensive. Faced with another project that requires quite a bit of wood-to-concrete mating, and remembering how much fun we didn’t have on the previous job, I figured it was time for a new plan. After doing a bit of research, I decided to invest in a Ramset MasterShot powder-actuated nail gun.

The Ramset MasterShot .22 Caliber powder-actuated tool was designed to make attachments to concrete and steel fast and easy. The MasterShot is capable of sinking nails from ½” – 3” long through steel, wood, and concrete. The “powder-actuated” end of the equation comes in the form of .22 caliber single shot powder loads. There are three levels of “powder power” to choose from, depending on the length of the nail you’re using and what materials you’re shooting through. The loads are color-coded: 2 (Brown), 3 (Green), and 4 (Yellow), with the higher numbers being more powerful. Here’s a quick look at the Ramset MasterShot from Home Depot:

http://youtu.be/mCz_mkjBi8A

Gunpowder And Three-Inch Nails – What Could Go Wrong?!

Sometimes we joke around a bit about the over-hyped CAUTIONS!! and WARNINGS!! that accompany pretty much every tool nowadays. This is one tool where they might be worth a read, assuming you’d rather not end up with one of this year’s Darwin Awards. A tool that can propel a 3” nail through steel and concrete qualifies as an exception to the “We don’t need no stinkin’ instructions!” line of thought. To me, anyhow.

ramset mastershot
Yes, I DO occasionally read the instructions…

The tool itself is pretty sturdy. It weighs in at just under 4-½ pounds, has a comfortable handle and a heavy-duty barrel. The Ramset MasterShot is simple to operate. To fire a nail (also referred to as a pin), just insert the nail into the end of the barrel. The nails come with a piece of orange plastic around the shank, which holds them centered in the barrel. Slide open the chamber, insert a cartridge into the breech, and close the chamber. Press the end of the barrel firmly against your work piece, pull the trigger, and BOOM – Part A is now attached to Part B! After firing, briskly open the chamber, and the spent cartridge will come flying out.

ramset mastershot
To load the Ramset MasterShot, first insert a nail into the barrel…
ramset mastershot
Slide the chamber open…
ramset mastershot
Insert your charge of choice…
ramset mastershot
And close the breech. Locked and loaded!

The following video from Ramset, which appears to be an internal informational clip, gives you an idea how the guns operate.

The Ramset MasterShot: Say Hello To My Little Friend!

I’m currently doing quite a bit of renovation work in a three-story duplex. It’s an old building, and the exterior walls are solid brick, around 10” thick, coated with plaster on the inside. The floors and ceilings are concrete, along with several of the interior walls. This sucker is SOLID! And solid is great, except when you’re trying to do certain things, like running wiring or plumbing, or attaching trim, or installing cabinets, or…actually, pretty much ANYTHING.

We had several chores that required introducing wood to concrete. The concrete floors have sleepers over them, with varying floor coverings over them. In the kitchen, there were plywood subfloors with vinyl flooring. Apparently there had been some long-term water leakage in the past, because parts of the subfloor – and the sleepers beneath – were totally rotted out.

ramset mastershot
The sleepers and subfloor needed a little attention…

After pulling out all the rotted wood and getting the area dried out, we cut and laid out some new 5/4” pressure-treated sleepers. I had bought some 2 ½” nails to hold them down. After donning safety glasses and hearing protection, I loaded up the gun, pressed it into the sleeper, and fired away.

ramset mastershot
Ready to attach a sleeper

Yikes. As I mentioned, the Ramset MasterShot can shoot any of three powder loads, with the yellow loads being the most powerful. Naturally, I had bought a box of the yellow; more power, more better, right? Well, apparently, not always. Thanks to a combination of more power and, apparently, some less-dense concrete in the target area, the nail went completely through the sleeper and buried itself in the concrete. At the risk of sounding like a coloring book, back to the big Orange store I went to fetch boxes of Green and Brown loads. It turned out that the Green loads were a go, and we had the sleepers attached quickly and easily.

ramset mastershot
The yellow loads were a tad too potent for this job.
ramset mastershot
Luckily, the brown and green loads let you dial it down a notch.

Over or under penetration is a fairly common occurrence, judging by comments made in various forums and other reviews. The concrete in some walls and floors may be much harder and denser than in others. The other material you’re shooting through will also affect the penetration, depending on how wet or dry it is, presence of knotholes, and so on. You’ll probably have to experiment with different loads until you find the one that sinks your pins best, without overdriving them.

I had a few that ended up protruding ¼” – ½” or so, and these were pretty easy to finish off with a hammer. I had a couple of others that stuck out over an inch. I had pretty good success finishing these off by using a second charge of the lightest load (the brown). I loaded up the cartridge – WITHOUT inserting a new nail in the barrel – and placed the barrel over the protruding nail. This worked pretty well to drive the nail flush, or very close to it. Again, experimentation may be required.

After finishing up our floor replacement, and putting a fresh layer of vinyl over it, we needed to re-install some of our kitchen cabinets. The Ramset MasterShot and some 2-½” pins had the base cabinets firmly attached to the wall very quickly. Since we weren’t sure what the shear strength of the pins was, we decided to use a different method to attach the wall cabinets. We did use the tool to attach new baseboards, and to attach some surface-mount electrical boxes and junction boxes.

ramset mastershot
Attaching the base cabinets was fast and easy.
ramset mastershot
Perfectly flush. You can finish driving the pins with a hammer if needed.

Other Ways To Nail It

In the powder-actuated tool universe, there are a variety of options. On a tight budget? There are hammer-strike models for around $26, that can handle nails up to 2-½” long. For fifty bucks, you can move up to a model that looks similar to the hammer-strike model, but has a trigger. Next in the lineup is the gun I bought, the Ramset MasterShot. These all use .22 caliber loads, and the beefiest one can sink nails up to 3” long. They can also shoot nails as short as ½”, and there are various sizes available, including nails with washers for extra holding power.

ramset mastershot
Fancy carrying case not included…

If you’re building a skyscraper or a bomb shelter, and you’ve got some serious, heavy-duty fastening to do, you can step up to the beefier, .25 or .27 caliber models. Many of these are “semi-automatic,” which means they take strips of ten nails, rather than having to load a single nail for each shot. Some can also shoot threaded studs. Prices range from a couple of hundred dollars up.

ramset mastershot
Nails with washers give more options for holding your “stuff” together.

The Ramset MasterShot did a great job in our project. It seems very sturdy, and we had no misfires or malfunctions at all while using it. When we did have serious overdriving a couple of times, the piston that drives the nails in actually protruded out the end of the barrel – and stayed there. After muttering some foul and unhappy words, I once again dug out the user’s guide (twice for one tool – a new record!) Fortunately, I discovered that it’s an easy fix. They recommend tapping the piston back in with a soft-nosed hammer, but I found a short piece of 2X4 did the trick just fine.

ramset mastershot
Way faster – and more fun – than screwing. With Tapcons.

The tool is very safe, if you use it properly. It won’t fire unless the chamber is closed, and the tip of the barrel is pressed firmly against the work piece. It’s relatively quiet, for something that fires a powder load, but I’d still recommend hearing protection. It has saved us a LOT of time and effort already, and we still have a lot of work to do on the second floor and in the basement. The expendables for it are reasonable and readily available, both online and in most home improvement stores. If your work involves attaching wood to concrete or steel on a daily basis, you’ll likely want a faster, beefier tool, maybe one of the .27 caliber models. For the serious DIYer, or someone who only occasionally goes off his meds to do this kind of work, the Ramset MasterShot should make your job a whole lot less miserable.

ramset mastershot

The Ramset MasterShot comes with a 90-day warranty. It’s available from Home Depot for around $90.

Buy Now - via Home Depot

Our new sponsor ToolAuthority.com is a GREAT source for Ramset tools, fasteners, “ammo” and parts, all with great prices.

Buy Now - via Tool Authority

Photo of author

About Phil

Phil’s path to the pinnacle of success as HomeFixated’s Senior Writer was long and twisted. At various stages of his life, he worked as a framing carpenter, attended motorcycle mechanics school, served as an Army MP, did a hot and itchy stint installing insulation in Phoenix, owned and operated a small contracting firm doing residential renovations, and worked as an employee of a major airline (Motto: We’re not happy ‘til YOU’RE not happy). He is currently semi-retired, but continues to take on little projects, such as the total renovation of an old farmhouse. Yes, he is a slow learner. Future projects include a teardown restoration of his 1965 BMW motorcycle, and designing and building a kick-ass playhouse for his grandsons. Phil loves spending time outdoors, hanging out with family and friends, cool tools, and a cold IPA when beer o'clock rolls around.

Subscribe to our newsletter

Get access to free prizes, product sneak-peeks, reviews, how-to's and much more!

More Info | Email Privacy

16 thoughts on “Ramset MasterShot – How To Nail It When It’s Built Like A Brick, Um, Outhouse”

    • Not unless you’re planning to attach the wood to concrete. It launches nails with a LOT of force. A nail gun or a screw gun would get the job done a lot more safely…

      Reply
    • Can I butter a slice of toast with a michette? Yes, but the part of me with a brain would feel stupid doing so. To do things properly, use the type of tool most people would use to do it. By now the majority of people have figured out the tricks long ago if they’re are any. If it’s not common practice, there’s likely a good reason behind it. I’ve never heard of anyone using a Ramset to build “a wooden fence”. Must be a good reason they aren’t.

      Reply
  1. As a 71-year-old DIY lady I too have a Ramset MasterShot and it worked great when attaching the floor plates to the garage floor to install a bathroom. Now I want to build a privacy fence above a cinder block retaining wall that’s capped with the same material. Would a lighter load work for attaching the 2×4’s to the retaining wall or should I use TapCon screws?

    Reply
    • Hi, Gypsy – I don’t know that either of those methods will give you a secure enough connection to keep a fence on top of a retaining wall. Normally you’d have beefy 1/2″ or 5/8″ lag bolts cemented into the wall and extending upward, where they would go through the bottom of a fence post connection bracket, and be attached with large washers and nuts. I don’t know what height your fence will be, what your weather (wind) conditions are, etc., but I’d be leery of making the attachment using nails or TapCon screws.

      Gotta say, though, you’re my DIY hero – I don’t meet many 71 year old women with questions about shooting nails into concrete, and who own the tools to do it! I would have a friendly chat with your local inspector, and ask what they recommend for your intended dimensions, materials, and location. Good luck – let us know how it turns out!

      Reply
  2. what if you drilled a 1/8 hole just through the wood kind of like a pilot hole so more energy at the concrete portion for penetration

    Reply
    • That might do the trick, especially if you’re shooting through thicker material. Good suggestion – I’ll have to give it a try next time! If anyone else tries it out, let us know how it works.

      Reply
    • My personal opinion would be that wood, except for solid knots, would represent a VERY small proportion of the resistance compared to concrete. I don’t think the wood fazes it one bit. It’s the concrete that is the real bugger. I have been fastening 2X4s to high strength cured concrete and even the .27 caliber Reds don’t seat properly with a 2 1/2″ pin.

      Reply
      • The closest tools allowing one to apply minimal human effort to build a wooden fence I can think of are A) a cordless drill, and B) a cordless framing nailgun. If you were to go back about 60 years, the tools would be A) a hammer, and B) a screwdriver. If I were to predict the future in 60 years, the tool will likely be A) a robot. Hehe

        Reply
  3. yes i have a ramset and it works good, but as you state it doesn’t always fully penetrate every nail. I have always hammered them in or left them out a bit if a stud wall, never tried reshooting it. Thanks for the tip!

    Reply
    • If they’re only sticking out 1/4 – 1/2″, I usually just whack them with a hammer too, Rich. Anything more, a light load usually does the trick…

      Reply
  4. I have a similar model at home, and we have a few models at work. There aren’t many tools that provide as much satisfaction as these do! The “semi-auto” ones are the best. Just walk down the work piece blasting away.

    Reply
    • You’re right, Mike – the first time I fired it, and felt how solid the connection was, I had my happy face on. Right after that, I started kicking myself in the butt for waiting so many years to get one. What a huge time and energy saver! As for the semi-auto, that would be sweet; Father’s Day is coming up, maybe time to start dropping some hints!

      Reply
    • Not sure, Sam, never saw Cliffhanger (don’t get out much). Definitely a fun tool to use, though, even if it is just for the hell of it. Very therapeutic!

      Reply

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.