Bosch MX30E Oscillating Tool Review – Should Fein Be Worried?

As an Amazon Associate we earn from qualifying purchases (more).

bosch-mx30e-mainWhen Germans square off against each other in battle, expect some serious engineering to start flying. For years Fein dominated the oscillating multi tool (OMT) market, but those days came to an end when their patent on the oscillating tech expired a few years back. Initial entries in oscillating tools often came up short on power. They also needlessly hassled users with the lack of a tool-free accessory change mechanism (which Fein has been sporting for many years now). Accessory changes are so frequent on oscillating multi tools, the lack of a quick change made me insane, or more insane. Bosch recently sent us their latest entry in the OMT market, the MX30E, which we’ve had a chance to test on several projects.

bosch-mx30e-access-lever
Accessory change lever locks open for fumble free accessory changes

Tool Free Accessory Change Lever

bosch-mx30e-ois
OIS at the business end
I still remember the frustration of using one of the original Fein MultiMaster tools which tortured me with a hex key for every accessory change. The key was also needed regularly to tighten accessories that would inevitably come loose at the most inopportune times. Fein resolved these issues with a tool free accessory change lever (and star shaped accessory mounts), and I’m happy to report Bosch has had similar success with the MX30. This Bosch oscillating tool features a lever that extends horizontally from the tool. While some other tool-free accessory change devices, like the one on Porter Cable’s oscillating tool, require continuous pressure during the accessory change, the MX30E’s lever locks open when fully extended. This makes accessory changes a breeze, and with the OIS accessory interface, returning the lever locks accessories in tightly while still offering the ability to rotate them easily as needed. The only downside to the tool-free design is that the lever can be a bit hard to get open if you’re wearing thick gloves. The tool free accessory change is unobtrusive, quick and effective, just as it should be.

bosch-mx30e-cable
Serious power delivered via serious strain-relief power cable

Power and Performance

bosch-mx30e-switch
Very accessible power switch
With a full 3 amps of power, the MX30E is unlikely to ever be referred to as underpowered. 3 amps doubles the power of some of the more consumer-oriented models on the market, and it even out-muscles Fein’s popular MultiMaster. If we did our Watt to Amp conversion properly, the Fein MultiMaster delivers a little over 2 amps. To outgun the MX30E, you’d need to step up to the very spendy ($700+) Fein SuperCut, which delivers over 3.5 amps. All that power comes at a bit of a cost in terms of weight. While the Fein Multimaster weighs in at around 2.4 pounds, we weighed the MX30e at close to 3.75 lbs. So while you can power through just about anything with the Bosch oscillating multi tool, you’ll be hanging on to more weight in the process.

Cutting and Sanding

ugly-pole-before
Pole before MX30E
As with other oscillating multi tools, one of the selling points is the ability to cut, sand and grind a wide variety of materials with minimum hassle and minimum dust. Thanks to the narrow range of motion, an oscillating tool doesn’t fling dust around like a whirring circular blade tends to. Like other OMT’s, this tool also excels with minimum effort; it functions best with very little pressure applied to whatever surface you’re working with. We tested the MX30E cutting lag bolts and cutting down a metal pole that has been a random and unsightly fixture in our yard for way too long. While cutting down the pole might have been better suited to a full size reciprocating saw, I turned the MX30E loose on it just for kicks. I worked my way around the perimeter of the pole and Bosch’s powerhorse blasted right through the metal.

bosch-mx30e-pole-cut-action
MX30E making short work of chopping down our metal patio decor

ugly-pole-after
Patio sans pole
Unfortunately, I didn’t realize the base of the pole where I was cutting was also filled with concrete. On a side note, if you ever want to instantly destroy a nice bi-metal cutting blade, try cutting concrete with it. Luckily I had cut most of the pole perimeter by the time I made that accidental slip into concrete, rendering the blade about as sharp as oscillating butter knife. Despite my obliviousness to the concrete, the Bosch MX30E performed admirably. As you can see, it also made our patio look a little more respectable. I also used the tool for some detail sanding around a large window I was replacing. As a sander, the MX30E felt remarkably smooth and powerful. In fact, it was so effective sanding that I had to dial back the power substantially. Sanding performance was great, but if you plan to be doing much of it overhead, the weight of this tool is a factor to consider.

Included Accessories
The last thing Bosch wants is for you to buy an oscillating tool from them and then have no accessories to deploy with it. As a result, the various kits Bosch offers contain a nice range of accessories to get you oscillating. Our hard case kit contained everything from various wood and metal cutting blades to carbide rasps to a scraper blade and sanding pad. Bosch also included a nice assortment of color-coded sandpaper. Red for wood, metal, fiberglass and plastic, and white for paint, varnish and filler. The only thing we really would have liked to see included in our kit or one of the other two kits is the optional dust collection accessory. Granted, most OMT tasks don’t generate a ton of dust, but for sanding in particular the dust collection attachment would definitely be handy for larger projects.

bosch-mx30e-accessories
Bosch includes this healthy assortment of accessories plus sanding sheets

This Oscillating Tool Still Doesn’t Go to 11

bosch-mx30e-power-dial
Still does not go to 11
We previously balked about select Bosch tools going from 1-6. We’ll continue our campaign for power settings that go to 11 in this post. Yes, we know, the number has absolutely no effect on performance. This is purely a marketing strategy here. Do you want a tool that only goes to 6, or do you want a powerful beast-of-a-tool that rocks your world with a power setting that goes to 11? Of course, the answer is clear. While we’re still stuck with 1-6, I should at least point out that the settings on the MX30E roughly correspond to speeds measured in oscillations per minute (or OPM). While setting 1 starts at a mild 8000 OPM, setting 6 delivers a full 20,000 OPM. Lower settings are typically adequate for most soft woods, with the higher settings coming in handy for hardwoods and metals. You’ll find the volume of the tool changes pretty significantly depending on speed, with the high settings producing a pretty significant whine (hearing protection recommended). While the top speed is just shy of Fein’s 21,000 OPM, we found 20k plenty of oscillations to work with. I personally can’t detect the difference between 20k and 21k OPM.

bosch-mx30e-barrel

Summary
If your idea of a great OMT project is cutting balsa wood dowels for your daughter’s doll house, then the Bosch MX30E is probably not for you. However, if you’re like most HomeFixated readers, you don’t cut much balsa. If you’re looking for a high power, take-no-prisoners multi tool with hassle-free and secure tool-free accessory changes, the MX30E delivers. All that power doesn’t come from a cordless toothbrush motor though. The MX30E is the heaviest and bulkiest oscillating tool we’ve tested, making it poorly suited to tasks like overhead sanding, tight quarters, or repetitive / longer duration projects where the tool is held with outstretched arms. On the flip side, the tool’s gusto powers through most cuts quickly and with minimal effort. So should Fein be worried? Let’s just say that Bosch and others have been rapidly closing the gap between Fein and everyone else in the OMT market. It’s another example of of the benefits of competition. While OMT’s were once a niche tool that only select tradespeople and hardcore DIY /tool enthusiasts would purchase, now, even the relatively high-end Bosch MX30E is downright affordable to both pros and homeowners. Viva OMT!

tyler-tool-mx30-options

Prices for the Bosch MX30E range from $199 – $289 depending on kit/case configuration, all well below the $400 Fein MultiMaster 250Q Top kit (which, in fairness, includes a dust collection accessory that is about a $30 accessory with Bosch). You can find the Bosch MX30EC-21 Multi-X 3.0 Amp Oscillating Tool Kit with 21 Accessories and the other Bosch MX30E kit configurations via Amazon:

Buy Now - via Amazon

Photo of author

About Marc Lyman

Marc grew up under a brave single mom who "encouraged" home improvement on the family home. Early toddler gifts included a tool set, and even a cordless Bosch drill when cordless drills first came out. In grade school (give or take a few years), Marc's mom said, "We need to cut down some trees. . . . here's a chainsaw." A father figure also involved Marc in many home improvement projects, including a summer of home remodeling in Palo Alto, CA. Toss in some Obsessive Compulsive personality traits researching everything home improvement related. The end result: a genetically pre-disposed, socially sculpted home improvement machine! For his complete profile, please visit our About page. Really, it's worth it.

Subscribe to our newsletter

Get access to free prizes, product sneak-peeks, reviews, how-to's and much more!

More Info | Email Privacy

12 thoughts on “Bosch MX30E Oscillating Tool Review – Should Fein Be Worried?”

  1. Mine is about 2 years old. I used it for typical home projects maybe about 30-40 times. Some how the OIS accessory holder shifted and i can no longer clamp on blades straight. And it sounds like it stalls. I’m thinking it’s the gearbox which through research must be purchased as an assembly for $142. I thought i was buying quality! Really disappointed.

    Reply
  2. Any experience using this tool to square rabbeted corners in hardwood cabinet doors? I’m still using chisels which make for a lot of work when working with oak, maple & mahogany. One common project for me requires 24 corners to be cut square for insertion of glass panes.

    Reply
  3. Just bought the MX30E and started toothing out an old maple floor. Blade changes with each board to cut nails and the board. I love everything about this tool, the only problem is after a few days use the release lever quit working. I am going to exchange it at Lowes where I bought it. I hope this isn’t a reacuring issue.

    Reply
      • Mine quick release lever just quit. Bought the tool a year ago, used it maybe 20 times in the past year. Nothing overly taxing for the tool. Too bad really. Its out of warranty. I’ll let you know what the repair costs!

        Reply
  4. Hi, I own both the Bosch here and the Fein[ older model ]. The new Fein has to much vibration. The old Fein and this Bosch model have none. I really am happy with this Bosch unit. Smooth, powerful , great blade lock system .Comfort and the ball end on the cord is also great. I bought mine with the L box. Lots of room for the tool and extras.

    Reply
  5. I’m looking for the best oscillating tool to D grout over 1000 hotel rooms and someone please help me give me directions of the best tool out there thank you

    Reply
    • Hey Vince! I’d definitely recommend corded. . . . and I don’t think you can go wrong with either Fein or Bosch. If you’re looking for even more heavy-duty take a look at the Fein Supercut (it’s spendy though). Good luck with the project!

      Reply
  6. I think the “low end” of the spectrum of the Bosch and Fein tools hit exactly the same price point. I own a recent Fein and love it but if I had to do it again I’d definitely consider the Bosch MX30E (especially given the extra power). The quick blade change is really key (or not since you don’t NEED a hex key to change the blade…. see what I did there?). Also, save that junked blade they work great for plunge cutting through drywall where you could literally strap a dull butter knife to the business end of the tool and it would work fein for cutting drywall (even if you’re using a Bosch OMT!). K, I’ll stop now.

    Reply
  7. Got to say the Skil I won has a hex key and just like the article says it comes loose at the most inopportune times. And of course this makes the blade changes difficult as well. But I’m still grateful to have it. I have rotting windowsills and this great little tool is perfect to cut out the rot without having to re-trim the entire window.

    Hopefully I’ll win a Bosch 😉

    Reply

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.