Delta Shower Doors – Design Your Own Shower Doors In Three Easy Steps!

As an Amazon Associate we earn from qualifying purchases (more).

delta-logoWhat's This?The last time we remodeled our master bathroom, Ronald Reagan was president, a first-class stamp was 24¢, and the Dow Jones Industrial Average was around 1,900. At the time, we tiled the walls and floor, put in a stock vanity and toilet, and installed a 4’ one-piece shower with sliding glass doors. A few years ago, we replaced the vanity, and the room still looks pretty good overall. Taking a closer look, though, the faucets are getting tarnished, and the glass doors are looking pretty dated and beat. Recently, the folks at Delta offered us an opportunity to try out a new service they are offering in conjunction with the Home Depot. Put down your copy of 1984, and take a look. We’ll show you how easy it is to customize and order your own Delta Shower Doors!

delta shower doors
The old 1980’s doors look ok from a distance…
delta shower doors
But a closer look shows it’s time to update.

The process is fast, easy, and almost fun—not an adjective you normally associate with buying a shower door. To begin, you first select what type of Delta Shower Doors you need—sliding tub, sliding shower, or pivoting shower. If it’s a shower door, you’ll need to know the measurement for the width; there’s a link on the first page that shows you where to measure.

delta shower doors
The Delta Shower Doors website shows what measurements you need.

At this point, you have two choices: choice one is to choose your door type and finish the design process online, which is simple and takes just a few minutes. Choice two is for those who hate doing anything online, or who just want to get out of the house, and perhaps go somewhere that has people strolling about in orange aprons, eager to help you get through the design process. It turns out Home Depot is the only place to go since Delta Shower Doors are available in-store exclusively there. Here’s a quick overview of the process from Delta:

Assuming you want to do it online, after choosing your door type, just click on the red banner that says “Step 1: Choose Your Glass.” Crazy as it sounds, this is where you’ll choose your glass. There are eight styles to choose from, including various patterns and textured glass. If you like to keep an eye on things while you’re showering, you can even select clear glass.

In the next step, you’ll choose the track for your Delta Shower Doors. You can select chrome, nickel, bronze, or polished brass. In each step of the process, prices are clearly shown for each option, and a little monitor on the upper right shows your selections so far, along with a running total cost. There is also a picture on each page, and whenever you make a selection, the picture is updated automatically to show what your door will look like.

delta shower doors
Designing your doors online is fast and easy…

The final step is to select your hardware. There are four styles of towel bars to choose from, depending on your tastes. If keeping it simple is your style, take a look at “Simplicity.” Looking for something with a bit more panache? “Panache” might be just the thing. The other two offerings don’t lend themselves to cheesy references; you’ll just have to look for yourself.

And that’s it, you just designed your own Delta Shower Doors! Just click on “See Your Design” to—you guessed it—see your design. At this point, you’ll also be able to look through several accessories that coordinate with your design, including faucet sets, towel bars, toilet paper holders, drawer knobs and even flush levers for your toilet! Click on “Add To Cart,” and you’ll be taken to the Home Depot web site. First, select your delivery method; you can choose to have it shipped to the nearest Home Depot for free, or to your home for a fee. Proceed to the checkout, pay, and sit back and dream how splendid your baño will look when your designer door arrives!

delta shower doors
Eight days after ordering, the Delta Shower Doors arrived

The order for my custom doors was placed on October 7th. On October 15th, a big ol’ truck rolled up, and a box of Delta Shower Doors landed on our side porch. Not bad, I’ve had stock special orders take longer than that to arrive. The doors are shipped by ground freight; when they get to your area, the trucking company will contact you to set up a delivery date. If you’re hiring someone to do the installation, tell them when to show up, and your mission is complete. On the other hand, if you have average DIY skills, and some basic tools, you can do your own installation. This will save you some money, and earn you the awe and respect of everyone you meet.

The HomeFixated Guide To Installing Your Delta Shower Doors

If your tub or shower is new, and you don’t have to remove an old set of doors, you have permission to scroll down to “Delta Shower Doors – By The Book.” Otherwise, the first step in the installation process is to make the old stuff go away. If your old doors are still in good shape, your local Habitat for Humanity or other salvaged-goods store may accept it for resale. This accomplishes several things: it eliminates your disposal problem (some trash haulers may not take large items), it keeps usable stuff out of the landfill, and you might even get a tax write-off!

Most shower doors are installed the same way: upright brackets go at either end of the shower, and are screwed into the edges of the tub or wall. A track fits in between them, and sits on the edge of the tub or shower. Finally, the top rail is attached to the top of the edge brackets. After all that is in place, you tip the doors into place, where little wheels glide along an overhead track. Usually there is a center bracket in the bottom track to separate the doors, and hold them into the track. To take it apart, we’ll simply reverse the process. And now for the first HomeFixated tip of the day: spreading a towel on the shower floor will help protect it, and will also keep screws and debris out of the drain.

First, pop out the old doors. Usually you can do this just by unscrewing the dividing bracket, lifting up on the doors, and tilting them into the shower. Once the doors are off, unscrew the side brackets and tip them in toward the center. There will probably be caulk wanting to hold them in place; use a painter’s multitool or a flat-bladed razor scraper to convince them to give it up; just be careful not to scratch your walls or chip your surround.

delta shower doors
First, remove the divider from the bottom track…
delta shower doors
Tip the doors in, and pop them out of the top track
delta shower doors
Carefully break the caulk bond…
delta shower doors
Unscrew the wall jambs…

At this point, you should be able to tip the sides and top outward. The bottom rail is usually just held in place by caulk; scrape it off, and the rail should pop right out. Use your flat-bladed razor scraper, and a sponge with some cleaner that’s safe for your shower’s surface, to get the rest of the caulk and years of accumulated nastiness off the entire opening area.

delta shower doors
Tip the header and wall jambs out…
delta shower doors
Break the caulk bond, and pry up the bottom track…
delta shower doors
Scrape up any remaining caulk
delta shower doors
Give it a good cleaning, and you’re ready for your new doors!

And that’s it, you’re ready to install your sporty new Delta Shower Doors! If you want to see how the pros do it, Delta has a series of helpful installation videos. The following is their sliding shower door installation video:

http://youtu.be/Y_Gef1b8SAY

Delta Shower Doors – By The Book

Even if you’ve done a shower door installation before, it’s a good idea to read the instructions. The instruction manual that comes with your Delta Shower Doors is excellent, very clear and thorough. The first page gives a list of all the tools and supplies you’ll need to install your doors, so a good first step is to round everything up. Unpack the doors and rails, and make sure all the parts are there. Some of the parts are stuck in the packing foam, so don’t pitch anything until your installation is finished. I’ll give an overview here, but the manual has much more detail, and is, as they say, profusely illustrated.

The wall jambs go in first. The jambs must sit flat against the shower wall and the threshold; if you have a tile wall, or a tub or shower with a perfect 90° angle where the wall meets the threshold, you’re set. If you have a tub or shower where there’s a curve there, you’ll need to round off the bottom of the side rails to conform to the curve. This is no big deal; the instructions tell you to use a coin to mark the contour onto the jamb. What they don’t tell you is that you probably won’t be able to SEE that mark!

delta shower doors
You can use a coin to mark the radius.

A little HF tip: put a piece of masking tape on the jamb, and make your mark on it. Use a pair of tin snips or a hacksaw, and cut to that approximate shape. Finish smoothing it to the right shape with a file or angle grinder. You can also use an angle grinder to do the whole process; that’s what I did, just be careful not to get carried away with it.

delta shower doors
Use snips, a file, or a grinder to shape the jambs.
delta shower doors
A good, tight fit in the corner.

Place the wall jambs against the wall, centered on the bottom ledge. Use your level to plumb them, then temporarily tape them in place. Next, you’ll drill a 1/8” pilot hole through the three pre-drilled holes in the wall jambs into the edge of the shower. Take the jambs back off the wall, and use a 5/16” bit to enlarge the pilot holes.

delta shower doors
Plumb up the wall jambs. Masking tape holds them in place.
delta shower doors
Drill 1/8″ pilot holes through the pre-drilled holes in the jambs.
delta shower doors
Remove the jambs, and enlarge the holes to 5/16″.

Push the supplied wall anchors into these holes, and snug them in gently with a small hammer. Reposition the wall jambs, and screw them to the wall. Your screws will be used to attach bumpers to the top and bottom holes, and a special center bumper in the middle. Hey—your walls are done!

delta shower doors
Push wall anchors into the 5/16″ holes unless you’re drilling into a stud…
delta shower doors
Screw through the bumpers and into the anchors.
delta shower doors
You’re jambin’!

Laying Some Track

Now it’s time to cut the bottom track. The kits will fit various sizes of tubs and showers; getting an accurate measurement will give you a good, snug fit you need to measure the distance between the two jambs. This can be tricky to do, as it’s an inside measurement. Here’s another HF tip: measure from one end to an even number around the center of the threshold, and make a mark. I chose 24”. Now, measure from the other end to that same mark, and add those two numbers together. My second measurement came to exactly 19”, making my total length 43”.

delta shower doors
Measure about halfway from one side of the track, and make a mark…
delta shower doors
Measure to that mark from the other side, and add ’em up.

Now you need to transfer that measurement onto your bottom track, and mark it for cutting. Our track hardware was bronze, which makes it really hard to see any marks. I used the tape trick again, putting a piece of masking tape on the track and making my mark on it. To avoid unnecessary foul language and elevated blood pressure, double check your measurements and marks before you cut! You want a nice, square cut, so use a miter box with your hacksaw. Make sure it’s deep enough to accommodate a 3” wide piece of material; that’s how wide my top track was. Make your cut, and use a file to smooth any burred edges. By the way, another tip the folks at Delta repeated several times was DO NOT CUT THE TOP AND BOTTOM TRACKS TO THE SAME LENGTH! They are correct, don’t do it!

delta shower doors
A piece of tape makes your mark easier to see.
delta shower doors
A basic miter box gives you a smooth, square cut.

There’s a piece of gasket material in the kit; slide it into the groove in the track, and cut it to length. Now test fit your track between the jambs. Undoubtedly, it’s a perfect fit; if not (due undoubtedly to a shoddily-made tape measure or something else beyond your control), remove the track and file it to size. When all is well, fill the groove on the bottom of the track with silicone sealant, and press it into place between the jambs.

delta shower doors
After test-fitting the track, apply silicone sealant underneath it…
delta shower doors
Insert the track between the jambs, and press it into place.
delta shower doors
Three sides finished!

Next up: the top track. For this, you’ll measure the distance between the two shower walls, above the wall jambs. This is another tricky measurement to get accurately. If you’re replacing a previously-installed unit, here’s a little cheat that worked for me: measure the OLD upper track, assuming it fit properly. Mine did, so it was easy to get the exact measurement. If you’re not so fortunate, here’s an easy way to get the measurement using materials at hand: take a piece of cardboard from the packaging, and make a mark exactly 12” from a square end of it. (Alternatively, you could use a 12″ ruler or a framing square). Hold the square end against one wall, and measure over from the other wall to your 12” mark. Add the two together, and there you go! Transfer the measurement to the top rail, again using a piece of masking tape, grab your miter box, and make the cut. Again, be sure to double-check your measurement first. De-burr the end, hold the top rail over the wall jambs, and push it into place. The hardest part is done!

delta shower doors
If you removed an old door, just measure the old top track.
delta shower doors
Mark the top track for cutting.
delta shower doors
Press the top down over the wall jambs.

I Can See Clearly Now – Or Perhaps Obscurely

And now for the most rewarding segment of your Delta Shower Doors installation, the shower doors! Remember the foam I told you not to throw away? That’s where the hanger brackets were lurking. Two brackets go on each door; the inside door gets installed first. The doors are identical, so grab one and install the hangars using the pre-drilled holes in the door, making sure the grooved sides of the brackets face the label side of the glass panel. Snug up the screws but don’t go all Incredible Hulk – you don’t want to risk cracking the door, and having to explain to your friends why there’s a blue tarp hanging in your shower opening. Now just lift the door into the upper track, until the rollers rest on the track. Make sure the side of the door with the label is facing in.

delta shower doors
Insert a bushing into the hole…
delta shower doors
Snug up the door hanger…
delta shower doors
When both hangers are in place…
delta shower doors
Lift the inside door into place on the inner rail.

Now repeat the process with the other door, but this time with the smooth side of the bracket facing the label side of the door. Lift the door into the top track, making sure the bottom of the door is inside the bottom track. Wow, it’s starting to look like a shower!

delta shower doors
Now repeat the process with the outer door, and lift it onto the track.

If the doors don’t meet the walls properly, they can easily be adjusted. Pop the door back out of the track, and loosen up the rollers. There are three holes the roller can be inserted into; to raise the glass, use the lower hole. To lower it, use the upper hole. Snug the roller up, and re-hang the door.

delta shower doors
To adjust the door, remove the screw that holds the wheel on…
delta shower doors
Use a lower hole to raise the door, a higher one to lower it.

Once the doors are aligned properly, it’s time to install the divider on the bottom track. Measure the bottom track, find the center, and position the divider there, with the doors in the grooves. Drill 1/8” pilot holes through the edge of the divider into the bottom track, and secure it with the two self-tapping screws. Your Delta Shower Doors are secure, and you’re almost finished!

delta shower doors
Center the lower divider, drill pilot holes, and screw it into place.
delta shower doors
Almost finished!

Sealing the Deal

To keep the water on the inside of your beautiful new Delta Shower Doors, take your silicone sealant and seal along the entire length of the wall jambs and bottom track, both inside and out. 100% pure silicone works best, and there are varieties made specifically for bathrooms, with mold inhibitors. All that’s left to do is install the door handles or towel bars you selected. The exact installation will vary according to your hardware, but all are designed to be used with the pre-drilled holes in the door.

delta shower doors
Use good silicone sealant around the entire inside and outside of the track.

Mine was very straightforward. I just inserted the rubber bushings into the holes in the door, slid a rubber gasket over the escutcheon and the handle post, and threaded them together through the hole. I installed one end, then put a bit of silicone on the towel bar, slid it into the post, and installed the other end. Easy peasy!

delta shower doors
No tools are needed for this towel bar, the pieces are threaded.
delta shower doors
Hold the back piece up to the door…
delta shower doors
insert the other side, and spin it snug.
delta shower doors
Towel bars in, and lookin’ good!

I summoned my wife, and we stepped back and admired the transformation, what a difference! It looked great, until I opened the door and saw the old faucets and drain. Replacing them will be our next move, the spiffy new doors made us realize just how crappy the old fixtures had gotten over the past three decades. Meanwhile, the Spousal Seal of Approval was issued.

delta shower doors
The new hardware highlights how beat the old fixtures are…
delta shower doors
But the doors look great!

Design Your Own Delta Shower Doors

I think the custom Delta Shower Doors concept is great. The materials are very good quality – the weight on the shower doors was about twice that of those I took out. Fit and finish is excellent, everything you need to do the installation is included, and the instructions are very good. The design and ordering process was quick and easy, and the available options should enable most buyers to design a set of shower doors that’s exactly what they want. The only quibble I had with the entire process was that it’s difficult to see exactly what the various types of glass look like, at least that was the case on my Mac. Some higher-res photos might help with that.

Pricing is very competitive with stock units, where you’re limited to whatever configuration happens to be on the shelf. With the Delta Shower Doors, you’re the boss. Don’t like pebbled glass? Go with the Mission style. Tired of the polished brass (yep!)? Get the rubbed bronze or brushed nickel. Got some fancy shmancy towel racks on the wall? Get a matching fancy shmancy towel bar on your shower door.

The flexibility is great, you can get exactly what you want, and you can control the cost. I designed a similar setup in chrome, with pebbled glass, and the total cost came to $210. You can further control your costs by choosing to pick up your Delta Shower Doors at a nearby Home Depot for free, but if your schedule is crazy, you can have it shipped to your home for $55 or so. The doors come with a limited five-year warranty.

delta shower doors
Before…(not bad from a distance; scary up close)
delta shower doors
And after–three hours after, to be precise!

Ready for the three-step program? Design YOUR custom doors before November 3rd, 2014, and you can enter a sweepstakes to win $1,000 or your own set of custom Delta Shower Doors!

More Info - via DeltaShowerDoors.com

Photo of author

About Phil

Phil’s path to the pinnacle of success as HomeFixated’s Senior Writer was long and twisted. At various stages of his life, he worked as a framing carpenter, attended motorcycle mechanics school, served as an Army MP, did a hot and itchy stint installing insulation in Phoenix, owned and operated a small contracting firm doing residential renovations, and worked as an employee of a major airline (Motto: We’re not happy ‘til YOU’RE not happy). He is currently semi-retired, but continues to take on little projects, such as the total renovation of an old farmhouse. Yes, he is a slow learner. Future projects include a teardown restoration of his 1965 BMW motorcycle, and designing and building a kick-ass playhouse for his grandsons. Phil loves spending time outdoors, hanging out with family and friends, cool tools, and a cold IPA when beer o'clock rolls around.

Subscribe to our newsletter

Get access to free prizes, product sneak-peeks, reviews, how-to's and much more!

More Info | Email Privacy

9 thoughts on “Delta Shower Doors – Design Your Own Shower Doors In Three Easy Steps!”

  1. I have a sliding shower door exactly like your old one, but silver/aluminum. Installed in 1989. I want to keep it as it is in great shape. On the bottom of the inside door, there are 2 holes about 2″ apart on either end. A plastic piece about 3 1/2′ long screwed into the holes, then extended straight down. There is a groove in the bottom track, on the inside of the shower. After that plastic piece goes down vertically, it makes a 90 degree bend and slips into the groove. This what keeps the door in place on the bottom.

    I’m curious what kind of door you removed (the gold one), if you know who the manufacturer is. I would like to see if they have these two plastic parts. Ideas? Thanks!

    Reply
    • Our old doors were installed roughly the same time as yours – late 1980’s. Unfortunately, I don’t know what brand the old doors were. For some reason, plumbing equipment manufacturers are notoriously bad about putting their name on their products; many times over the years I’ve had problems trying to repair faucet sets and the like, because there is no indication who the heck made them.

      That said, sometimes they DO put their name on there somewhere. Take a look and see if it might be stamped inside the edge brackets, or the top or bottom tracks. If the faucet set was installed at the same time, there’s a chance it might be the same brand.

      As a last resort, take some good pictures, and try a plumbing supply store (as opposed to the plumbing aisle in a big box store, which is less likely to have parts for something that old and specialized). Hopefully they can come up with something that will work, and get you back on track. Good luck!

      Reply
  2. Those new doors looked really good. I have some clearer doors that I’m trying to update. I like the look of your cloudier doors. They look sophisticated without looking just not clean. I think I’ll have to look into this to get the glass I want. Thanks.

    Reply
    • Thanks, Fred, we’re very happy with them. With the rain-patterned glass, they’re a lot easier to keep looking good than plain glass. We usually just wipe them down with a squeegee, and they look fine. The inside (shower side) of the glass is smooth, so they’re easy to wipe off.

      Reply
  3. Well have to say I was excited but then realized that these do not cover all sizes of openings. So if you have a shower opening over 36 you are SOL. Very disheartening… My shower has a 42″ opening. I do not want sliders as my shower has to accommodate some one in a wheel chair. Guess Delta is not concerned about the handicapped.

    Reply
    • Hi, Dave-

      Delta makes a lot of handicapped-accessible and ADA compliant plumbing fixtures, so my guess is that this is more an issue of trying to have this particular line of products focus mostly on the most common shower sizes, so they can provide quick turnaround.

      I’m actually in the process of installing a 42″ shower on the first floor of our old farmhouse, and I hadn’t yet explored the door options. It’s really too narrow for sliders, and while there are 42″ pivoting doors available, they are stinking EXPENSIVE! We will probably end up just using a shower curtain; not the greatest solution, but what best fits the budget at present. If I come across a better option, I’ll post it here.

      Meanwhile, I forwarded your comment to the folks at Delta; we’ll post any response we get. Good luck in your search, and if you find a good option, please let us know.

      Reply

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.