Flocking – How To Use It

As an Amazon Associate we earn from qualifying purchases (more).

Featured Image

If you want the inside of your project to look as good as the outside, flocking just may be what you’re looking for. Made of shredded felt fibers, flocking babies your treasures on a soft, scratch-free, durable surface with lots of visual appeal. Sure, you could just caveman it and leave your drawers all rough and natural. You could also polish your precious heirlooms with a rasp. But if you want a professional quality liner that’s easy to install, read on and I’ll show you how it’s done.

Meet The Flockers

Flocking
Flocking fibers, adhesive and cardboard flocker.

Flocking is available in a couple dozen colors. My go-to is royal blue because it works well with just about any wood, light or dark. My personal stock also includes brown, red, green and yellow, colors I tend to use only by special request. Some choose to finish their drawer and box interiors by gluing in sheet felt or velvet, both of which often leave unsightly seams and sometimes curl at the corners and edges over time. Flocking feels like velvet and installs seamlessly; the perfect solution to a problem you never knew you had. Try to ignore those ugly seams now!

Drawer
When lacquering drawers, I also spray the interior with a couple thin coats to start sealing the grain.

I always use clear spray lacquer on projects that I intend to flock. Other film finishes (polyurethane, for example) should work as well but, when in doubt, test on scrap wood with the same finish before putting your project at risk. Penetrating oils – linseed oil, walnut oil, teak oil, and so on – can prevent the adhesive from bonding securely so I recommend avoiding such finishes on items you plan to flock. The same goes for waxy finishes.

In my shop, flocking – if used – is always saved for the final step of a project. Apply your finish and let it cure completely before moving on.

Read The Grain

Grain direction
Note the grain direction in this drawer. The bottom of the drawer is end grain and should be sealed for best results.

Flocking adhesive is essentially a thick oil based paint tinted to match the fibers. Paint – like other finishes – tends to wick into open wood pores. That can spell cosmetic disaster on drawers and boxes having thin end-grain sections. It’s important to seal the end grain to prevent colored adhesive from bleeding through and staining the exterior of the project.

When I lacquer the exterior of my projects, I always hit the innards with a couple light coats as well to begin sealing the pores. Next, I note which direction my grain runs. On the drawer pictured above, you can see that the grain runs vertically. With vertical grain, the bottom of the drawer is most vulnerable to bleed-through because that’s where the exposed end grain is. Depending on the design of a given project, the grain may run from side to side, front to rear or diagonally. In the case of burl wood, the grain may even be a chaotic swirl.

Seal of A-glue-val

Seal the pores
Fill the pores with white wood glue.

After identifying the grain direction, seal the surface to be flocked by rubbing white wood glue into the pores with your finger. You don’t need to go crazy with the glue; just be sure to clog all of the end grain. Wipe off any standing puddles and set it aside to dry for a few hours.

Backwards Masking

Masking
The masked off areas will not be flocked.

Now that the glue is dry, use masking or painter’s tape to cover the areas you don’t want to flock.

One Liner

Plastic liner
Line a shallow cardboard box with a plastic trash bag.

A cardboard belt is a waist of paper. A cardboard box, however, is just what we need. Line the box with plastic sheeting to make cleanup a metaphoric breeze. After all, a real breeze would make cleanup a nightmare.

Tubal Emblazon

Top of flocker
The fibers are blown out of these holes in the top of the applicator tube.

A cardboard flocking applicator (a “flocker”) is a two piece telescoping tube used to blow the fibers onto the adhesive paint. Other methods – pneumatic, electrostatic, and violent shaking – do exist, but this is the best and most practical option for the DIY’er.

Loading the tube

Use the bottom half of the applicator (the one without holes) to scoop up more fibers than you think you’ll need. But don’t fill the tube completely.

Fibers in tube
I scooped up about a ½ cup of fibers.
Reassembly
Reassemble the flocker.

Color Me Impressed

Mixing
Thoroughly mix the adhesive before applying.

Once you start painting on the adhesive you’re up against the clock. If the paint you’ve already applied skins over on you halfway through the process, the fibers aren’t going to adhere worth a crap. So don’t try to flock too many drawers at one time. It’s also important to have your work area and loaded flocker ready to go before proceeding.

Apply a generous coat of adhesive with a soft haired brush. I use a natural hair artist or acid brush. Synthetic brushes just don’t work as well and may require some patches to be dabbed for sufficient coverage. Anywhere that wood shows through will be starved and end up resembling a mangy mutt: pretty flocked up. So, if you still see wood, you need to add a little more adhesive.

Applying adhesive
Don’t be stingy with the adhesive paint.

Flocking And Blowing – Not Just An Expression

To use a flocker, gently pump the inner tube in and out of the larger one. Short strokes at a rate of about two per second works best for me. Adjust your technique as needed. Start by turning the flocker vertically so all the fibers fall to the bottom. Then hold it horizontally and start pumping gently.

Blowing the fibers
Gently blow the fibers onto the paint.

Slowly raise the back end as shown until fibers are blown out of the holes as a cloudy mist, not a clumpy mess. At first, concentrate on the tightest inside corners, followed by the more obtuse corners. As you do this, the larger surfaces will receive a dusting of fibers as well. Take your time and really saturate the adhesive. As soon as the fibers soak in and expose paint, dust it with more fibers.

Fibers applied
Be very liberal with the fibers.

After you’ve got a good start on the corners you can work more on the larger surfaces. But continue tending to the corners as well. When you feel like you’ve got a good enough coating of fibers: blow on more. Once you’ve done that, add even more. A good flocking job requires a glut of fibers, and then some. In the end, the adhesive should be saturated to maximum capacity.

Overkill this step with every fiber of your being. Then set it aside to dry for a day. Don’t worry about wasting your flock. The excess is still perfectly good and will be reclaimed with no problem.

Lots Of Fiber. Big Dump.

Excess fibers
Pour out the excess fibers.

Now that the flocking has had a full day to cure, go ahead and dump out the excess fibers and remove the tape.

Unmasking
Peel away the masking to reveal the beauty.

Use a soft brush to whisk away any loose fibers, especially in the corners.

Brushing away excess
Gently brush away any loose flock.

Touch Up

Slop
Here is some paint that seeped underneath the tape.

It’s almost inevitable that a little adhesive will get under the tape in some areas. The act of painting it on often forces it in around any rounded or chamfered edges. As long as you discover the issue within a day or two it can easily be cleaned up with a little mineral spirits on a folded up paper towel or rag. That’s another reason why you should always apply your finish before flocking. On bare wood, any stray adhesive will leave a permanent stain.

Mineral spirits
Mineral spirits (paint thinner) makes quick work of any sloppy edges.
Before and after
Before and after. A paper towel lightly dampened with mineral spirits (paint thinner) makes the paint edges nice and crisp.

Reclamation

Reclaim the excess
It’s easy to reclaim the excess fibers for future use.

As alluded to earlier, it’s impossible to use too much fiber. Simply scoop up the excess with a paper card and throw it back into the bag for next time. No worry; no waste.

The Proof Of The Flocking Is In The Flaunting

Band saw box
One of my many band saw box designs.

When I make band saw and other keepsake boxes, I always flock the interiors. The difference is night and day. Once you flock you’ll never glue in felt or fabric again. And bare drawer interiors will feel like concrete by comparison. It’s time to step up your game! Now flock off, will ya’?

Finished drawers
Oh yeah… That’s the stuff!

Flocking can be obtained from a number of woodworking and craft suppliers, including our sponsor, Rockler.

Buy Now - via Rockler

Photo of author

About Steve

Steve made his first woodworking project at age 9 (in 1982) and whittled his first wooden chain at 18. He was also a consumer electronics repair tech and shop owner for a little over 20 years, until his impending obsolescence became impossible to ignore. Since then, Steve has focused passionately on manipulating his wood... in his workshop. Don't judge him.

Subscribe to our newsletter

Get access to free prizes, product sneak-peeks, reviews, how-to's and much more!

More Info | Email Privacy

17 thoughts on “Flocking – How To Use It”

  1. Hi, I used this same process and have some strange areas that need more fibers. Have you ever had to re-apply more fibers to an already flocked box? If so, any tips? I was thinking about using spray adhesive but not sure if this will look sloppy.

    Reply
    • Tania, I know you’re question was posted a year ago (sorry). If I were to reapply flocking, I’d scrape and sand away the old as best as I could. Then start fresh with flocking adhesive followed by fibers. Trying to apply new over old isn’t likely to give the results you’d want.

      Reply
  2. Hey Steve, I’m glad that I found you here and that I found this flocking material. I knew about this stuff early on, but when I looked for it more recently people took my inquires mostly as vulgarity, and though I had a need to adorn some of my gift boxes, I discontinued my search for the stuff. Thank you steering me in the right direction once again. Ralph – aka: Art Rafael

    Reply
  3. I was also blessed with family members who were real tool, equipment, etc. “nuts” (for lack of a better word at the moment). They exhibited a genuine love for buying quality items … so many things fall victim “planned obsolescence”. I also enjoy the humor you interject into your writing.

    Anyway, just wanted you to know …

    Reply
    • I appreciate the feedback, J T Fukushima! Along with a little knowledge and inspiration, tools usually possess the ability to dodge obsolescence. Tools are empowering. Tools make life easier. Tools give creativity a stage on which to perform. Yup, I’m a tool nut for sure!

      Reply
  4. Interesting process, did not know it is such an involved process! Certainly adds a quality plus to projects! Can you flock with a rainbow of colors?? I can imagine a lovely “stained glass” effect being quite pretty. Thanks for the info, Steve appreciate learning something new.

    Reply
    • Thank you for reading, Linda Derrington. It may difficult to get crisp details and sharp borders between adjacent colors. But yes, you can flock multiple colors and patterns. I like your idea though. I may have to try a stained glass-style pattern sometime 🙂

      Reply
  5. I always wondered how that was done. Understanding the process gives you a better appreciation for the finished products.

    Thanks, Sherry

    Reply

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.